How to Identify and Remove a Burr When Sharpening a Knife
A consistent sharpening angle helps establish the edge, but finishing also requires attention to the burr. A knife may cut well while still carrying a thin metal extension along the apex.
This guide explains how to identify and address a burr on conventional double-bevel steel knives.
What Is a Burr?

A burr is a thin extension of metal beyond the intended cutting edge. It can form as metal near the apex—the point where the two bevels meet—bends away from the abrasive.
A small burr can indicate that sharpening has reached the apex in that section. However, a burr changing sides may simply be folding over rather than being removed.
Keep it small. Grinding longer to create a more noticeable burr removes unnecessary steel and can make finishing harder.
How to Check for a Burr
Clean the blade and inspect both sides under bright light. Slowly change its orientation, looking for a fine projecting lip along the heel, middle, belly, and tip. A loupe can help.
Reflections may also come from damage or a rounded edge. Small or aligned burrs can be difficult to see, so combine inspection with a controlled cutting test. Avoid sliding your fingers along the edge.
If you are unsure whether the abrasive is reaching the apex, use the marker test described in our freehand angle-control guide.
How to Reduce and Remove a Burr
1. Establish the Edge
Choose a starting grit suited to the blade’s condition. A coarse abrasive removes material efficiently when restoring an edge; a finer abrasive may be sufficient for light touch-ups.
Work until both bevels reach the apex along the intended cutting edge.
Dual-grit stones such as the SHARPAL 162N provide coarse and fine surfaces for these different tasks. See our Diamond Sharpening Stone Grit Guide for grit selection.
2. Reduce Pressure and Alternate Sides
As you approach finishing, reduce the number of passes on each side and alternate sides more frequently. Alternating single passes can help you work evenly, but inspection should guide how long you continue.
Use light pressure on diamond plates, reducing pressure further during finishing. On a hard bench stone, controlled edge-leading passes can help reduce the burr: move the cutting edge into the abrasive while maintaining the intended sharpening angle.
If the burr keeps switching sides, check that the abrasive contacts the apex on both bevels. Use the marker test if needed, and check whether you are pressing harder than necessary. Continue in short sets, inspecting between them.
3. Refine the Edge
If coarse sharpening was needed, move to a finer abrasive to refine the scratch pattern and continue addressing the remaining burr.
Maintain the intended sharpening angle and finish with light, alternating passes. Inspect the entire edge, including the heel and tip.
Finer grit changes the edge finish; it does not automatically remove a burr. Choose the finishing grit according to the intended use rather than progressing to higher grits by default.
4. Optional: Refine With a Leather Strop
After fine sharpening, a leather strop can help refine the edge and address small residual burrs. A dedicated strop such as the SHARPAL 204N can be used at this stage.
Use light, edge-trailing strokes: the spine leads and the cutting edge follows. Lift the blade clear before turning it over. Excessive pressure or angle can round the apex.
If a pronounced burr remains or either bevel has not reached the apex, return to the sharpening abrasive. Stropping cannot replace incomplete sharpening.
How to Check the Finished Edge
Clean and dry the knife, then carefully cut a sheet of paper with your fingers clear of the cutting path. Check the heel, middle, and tip for repeated catching or tearing.
Inspect any section that catches consistently. Residual burr, remaining damage, or incomplete sharpening may need attention.
A clean paper cut is useful feedback, but an aligned burr can also cut. Assess cutting performance alongside visual inspection rather than treating either check as proof of complete burr removal.
Final Thoughts
Effective burr removal starts with establishing the edge on both bevels. Keep the burr small, control pressure during finishing, and inspect the entire edge.
Choose abrasives for the work required and use leather refinement when appropriate. Let the edge’s condition guide further sharpening.

